KOR
Reinforcing Bar
Home
Products
Reinforcing Bar
Dimension & Unit Weight

Reinforcing Bar

Products>Reinforcing Bar>Dimension & Unit Weight
  • 철근
  • 철근
  • 철근

Reinforcing Bar

HANSCO products are produced with the latest equipment and superior technologies. Even a small product is strictly controlled for the production of products demanded by customers. In the case of high-strength reinforcing bar such as SD400, SD500, and SD600 among our manufactured products, we produce reinforcing bar with superior quality by forming a hardened layer through a rapid cooling process on the surface with water cooling (TEMPCORE) reinforcing bar production method. In addition, we are manufacturing products with various specifications and sizes including special reinforcing bar and seismic proof reinforcing bar according to the rising demand for high-strength seismic proof reinforcing bar. We will continuously respond to the demands of our consumers through constant research & development.

Dimension & Unit Weight

좌우로 스크롤 하시면
내용이 보입니다.

치수 및 단위무게에 대한 정보
KS D 3504 ASTM A615
Designation name Unit weight Nominal diameter
d
Nominal cross section
S
Nominal perimeter
l
Max. average spacing of transverse rib Average height of transverse rib Maximum value of sum of the gap of transverse rib Designation name Unit weight
Minimum Maximum
kg/m mm mm2 mm mm mm mm mm lb/ft kg/m
D 10 0.560 9.53 71.33 29.9 6.7 0.4 0.8 7.5 3 0.376 0.560
D 13 0.995 12.7 126.7 39.9 8.9 0.5 1.0 10.0 4 0.668 0.994
D 16 1.56 15.9 198.6 50.0 11.1 0.7 1.4 12.5 5 1.043 1.552
D 19 2.25 19.1 286.5 60.0 13.4 1.0 2.0 15.0 6 1.502 2.235
D 22 3.04 22.2 387.1 69.8 15.5 1.1 2.2 17.5 7 2.044 3.042
D 25 3.98 25.4 506.7 79.8 17.8 1.3 2.6 20.0 8 2.670 3.973
D 29 5.04 28.6 642.4 89.9 20.0 1.4 2.8 22.5 9 3.400 5.060
D 32 6.23 31.8 794.2 99.9 22.3 1.6 3.2 25.0 10 4.303 6.404
D 35 7.51 34.9 956.6 109.7 24.4 1.7 3.4 27.5 11 5.313 7.907
D 38 8.95 38.1 1,140 119.7 26.7 1.9 3.8 30.0
D 41 10.5 41.3 1,340 129.8 28.9 2.1 4.2 32.5
D 43 11.4 43.0 1,452 135.1 30.1 2.2 4.4 33.8 14 7.650 11.38
D 51 15.9 50.8 2,027 159.6 35.6 2.5 5.0 40.0
D 57 20.3 57.3 2,579 180.0 40.1 2.9 5.8 45.0 18 13.60 20.24
Remarks
  1. 1) Nominal cross section (S) = 0.7854 x d2 : It is ended at the fourth digit of the significant digits.
  2. 2) Nominal perimeter (l) = 3.142 x d : It is ended at the first digit below the decimal point.
  3. 3) Unit weight = 0.785 x S : It is ended at the third digit of the significant digits.
  4. 4) Weight of 1 = Unit weight x length : It is ended at the second digit below the decimal point.
  5. 5) Weight of 1 group = Weight of 1 x count : It is ended with integral number.

Dimensional Tolerance

좌우로 스크롤 하시면
내용이 보입니다.

치수 허용차에 대한 정보
Classification Tolerance
Minimum Maximum
Height of transverse rib Below D13 4.0% of nominal diameter 2 times the minimum value
Exceeding D13, Below D19 4.5% of nominal diameter 2 times the minimum value
Over D19 5.0% of nominal diameter 2 times the minimum value
Length Below 7m + 40mm
0
Exceeding 7m Every time the length of 1m or its singular number increases, add 5mm to the tolerance above. However, maximum value shall be limited up to 120mm.
Remarks
  1. 1) It is not applied to a coil.
  2. 2) Dimension besides standard length follows the discussion between the orderer and manufacturer.
TOP